Product Search
Search results for 'C-1231'
Showing 61 - 80 of 1122 Total Results
Curing Rack, 4" x 8" Cylinders 12/ctn
CA-0219
Location: Parts & Accessories
These durable racks are manufactured from plastic compounds and recycled materials to resist moisture, abrasion, chemical and temperature variations. Each rack has built-in handles, making them easy to carry and safely stacked 12 tiers (58") high. The racks unique open frame design allows water...
(3) options
Location: Liquid Limit Machines
Liquid limit machines from Test Mark are part of a complete line of soil testing equipment and supplies.
CA-0793
Location: Min/Max Thermometers
Eliminates all of the problems associated with mercury separation and air bubbles trapped in traditional thermometers. Weather resistant rugged plastic case for outdoor use. Displays three independent temperature readings of current, maximum and minimum since last reset.
Dynamic Cone Penetrometer only
SA-1225
Location: Dynamic Cone Penetrometer
The Dynamic Cone Penetrometer (DCP) uses a 15 lb. steel mass that falls 20" and can be used effectively in augured holes to depths of 15 to 20 feet. The DCP features a heat treated cone and zinc plated components.
AA-0095
Location: Vacuum Pump
Direct-drive, two-stage, rotary-sliding, vane-high vacuum pump features a gas ballast and trap to reduce risk of oil being sucked into the system.
CA-0360-P
Location: Slump Testing
Test Mark's plastic slump cones for concrete testing are more economical than metal cones and will not rust or dent.
Feeler Gauge Set, .002 to .025
CA-0485
Location: Planeness/Thickness Gauges
When used with the steel parallel bar, Test Mark's feeler gauge will determine the planeness of testing machine platens, cylinder cappers and other testing accessories.
SA-3500
Location: Mud Balance
Mud Balances are used as standard procedure instruments for testing water and oil-base drilling fluids and oil well cements.
(41) options
Location: Air Meter Replacement Parts
Concrete air/pressure meter replacement parts are available from Test Mark. Use our diagram to find the part you need for easy online ordering.
CA-2965
Location: Comparator, Length Change
Gauge studs have stainless steel contact points for use with prism molds. Sold 10 per package. Part of our comparator/length change products.
SA-0241
Location: Soils
Adapter Foot is recommended when testing extremely low strength cohesive soils.
AA-0068
Location: Vacuum Pycnometer (Rice Test)
The vacuum pycnometer from Test Mark is used for determining the maximum specific gravity of bituminous paving mixtures with a maximum aggregate size up to 3/4-inch and a 2,000 g capacity.
MA-0135
Location: Concrete Cylinder Loading Shelf, CM-2500 Series
Easier loading of 6” cylinders in CM-2500 series machines. . This optional shelf was designed to make loading and positioning of 6” (152 mm) cylinders with pad cap rings both easier and safer in a CM-2500 series machine. The shelf features a heavy-duty steel design with a plastic laminated top, so...
CA-1570
Location: Field Rocker Screen Set
The field rocker screen set from Test Mark Industries consists of a 12-inch square steel frame with interchangeable wire cloth and bottom pan.
CA-1310
Location: Hot Plates
These durable hotplates are equipped with thermostatic temperature control. Baffle-vented welded stainless-steel case and cast-aluminum top for maximum heat transfer, strength and corrosion resistance.
SA-2030
Location: CBR Accessories
Used in the application of surcharged loads on the soil's surface during soaking and penetration. Rust-resistant.
SA-2031
Location: CBR Accessories
Used in the application of surcharged loads on the soil's surface during soaking and penetration. Rust-resistant. Slotted.
SA-0340
Location: Resiliency Tester
The Resiliency Tester is used to test resiliency of hard rubber base of liquid limit machines, which should be done at 90-day intervals to ensure base is in compliance with ASTM Standards.
Density Drive Sampler, 3" ( 76.2 mm)
SA-1355
Location: Density Drive Sampler
The density drive sampler from Test Mark determines in-place density of soil by driving a thin-walled tube into the soil mass to obtain a relatively undisturbed sample. 3" model.
